Most ceramic salt and pepper shakers require a stopper of some sort - usually cork - to keep the contents in. But there is a way to make them without stoppers. Just throw a double-walled vessel, but instead of joining the inner and outer walls, form a funnel with the inner wall.

 

In today’s post, potter Keith Phillips explains the stopperless salt and pepper shaker process in greater detail (and with great step-by-step photos!). – Jennifer Harnetty, editor.

 


 

Process

 

Click to enlarge!

Depending on the size of your hands, the amount of clay will vary between 3/4 to 11/4 lbs. I don’t have overly large hands, but when throwing these with less than a pound, it’s difficult to get my fingers where I want them to go. However, if the forms are too large, they are difficult to use. Center the clay and press your finger all the way down until you reach the bat. You want the opening to be about an inch or so in diameter.

 

Create a stair step in the ring by lifting your finger to about halfway up on the inside of the ring and pressing outward toward the side wall, which will open the sides more (figure 1). Leave about a ½-inch thickness of clay between your finger and the outer edge of the ring (maybe even more). Now, press down on the step, leaving enough clay to pull up your inside funnel (figure 2). You are essentially making a double-walled vessel, but the inner wall is actually a closed cone form. You will find you really don’t need much clay to create this inner funnel. It’s all about using your fingertips and pinches to pull the walls up. Try to pull it up to about 2–3 inches in height.

 

Once you have the funnel high enough, collar it in and close it off. Try to just close off the top, you want the funnel hollow, not solid, because later you will want to drill your hole and you don’t want to have to drill forever (figure 3).

 

 


 

Great ideas in every issue

Projects like Keith Phillips’ salt and pepper shaker appear in every issue of Pottery Making Illustrated. You’ll discover so many techniques to try in each issue, you’ll have trouble deciding where to start! PMI is the only ceramic art magazine dedicated solely to practical techniques for the intermediate to advanced clay lover.

Check it out 

 

 


 

Click to enlarge!

I also flatten the top of the funnel slightly. I think this helps catch more salt when shaken. Take a sponge and mop up and extra water in the recesses.

 

Now pull your outer walls up. You want this wall to easily clear the height of the funnel, and you want plenty of room between the top of the form and the top of the funnel or else salt won’t be able to travel in and out (figure 4).

 

At this point you have an opportunity to play with the form and make it your own. I tend to like the architectural feel of these little towers, but I’ve seen fruit, balls, squares, and every shape in between (see page 32). Once you’ve raised the outer wall enough that it clears the inner funnel, sponge out any water and collar in and close the form at the top (figure 5). Once the form is closed, air is trapped inside and the vessel begins to act like a balloon when altered or ribbed (figure 6).

 

After you have the shape you want, smooth the surface and add finishing touches with a rib (figure 7). At this point, pulling it off the bat is essential for me. Inevitably I either forgot to and/or can’t reach a sponge into the center to mop up any extra water that has collected inside the funnel. Removing it from the bat allows excess water to evaporate through the bottom. At the same time, throw a small chuck about the same diameter as the shoulder of your vessel. It should dry alongside your shaker

 

 

When both are leather hard, I use a combination of the Griffin Grip and a chuck to trim a shaker with a pointed top like this (figure 8). If your shaker is flat at the top or just slightly rounded, a chuck is probably unnecessary. If you don’t have a Giffin Grip, simply center, then attach your piece (or your chuck) to the wheel head using four balls of clay, or place slightly rounded forms onto a small ring or coil of clay. When using a chuck, remember to check that your piece is level using a bubble (torpedo) level before starting to trim.

 

 

FInished salt and pepper shakers by Keith Phillips

Define the width of your foot ring and trim the bottom. Trim both the outside edge and the area leading into the funnel to remove excess clay and refine the shape, but try not to let any shavings fall into the funnel as you work (figure 9).

 

Drill a hole into the top of the funnel from the bottom (figure 10). I’ve found an 1/8 inch drill bit is just about the perfect size. This lets a fair amount of salt in easily, without dumping too much when you are dispensing.

Glazing is pretty simple, just make sure no glaze gets inside the funnel or closes the hole. If you dip, just hold it upright and dip it into the glaze, the air trapped inside will keep the glaze from entering the funnel. After glaze firing, fill the funnel with salt or pepper. You may have to give it a gentle shake to help the salt travel down. Once it’s full, flip it right side up. The salt will fill into the vessel.

 

To dispense, simply give it a little shake over your food and salt or pepper will find its way to the hole and sprinkle out.

Tip: Do NOT place stopperless shakers in a dishwasher. If water gets inside the shaker, it is nearly impossible to dry out. Just wash the outside with a damp rag and soap.

 

Keith Phillips is a full-time artist and potter in Fletcher, North Carolina. To see more of his work, go to khphillips.etsy.com or visit his blog at blog.mudstuffing.com.

 

 


 

For more interesting wheel throwing techniques, download your free copy of Five Great Pottery Wheel Throwing Techniques: Tips on Throwing Complex Pottery Forms Using Basic Throwing Skills.

 

 


 

 
 
Click here to leave a comment