[kgtys]

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

[Marcia Selsor]

kgtys, on 20 April 2013 - 11:25 PM, said:

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

I didn't see a link to a picture. Are you familiar with Stephen Lee's work?
Marcia

[Chris Campbell]

No image seen but to answer your question, yes you could build one pot ... Wait til it is cheese hard ... Cut if up / crack it ... any way you want and re-assemble it using slip made from the same clay.

[Cathy Linfield]

kgtys, on 21 April 2013 - 12:25 AM, said:

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

You might try slicing almost all the way through the pot when it is almost leather hard, let it dry further then slice all the way through. Make sure you low fire for a couple hours...OR.... put it in your oven and take it from 100F to 350F in 3 hours....Slow drying will help it to not crack further . Cathy

[Marcia Selsor]

Stephen Lee is the Director at the ARchie Bray and recently open a show in NYC. Some pieces were from this series
http://www.ferringal...nt_8303_374.jpg

Marcia

[Chris Throws Pots]

Check out Jeff Campana's work. http://jeffcampana.com/

[Chris Campbell]

Chris Throws Pots, on 21 April 2013 - 01:57 PM, said:

Check out Jeff Campana's work. http://jeffcampana.com/

Thanks for this link ... Terrific work and a most interesting process.

[kgtys]

Posted Today, 10:25 PM

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

[kgtys]

Cathy Linfield, on 21 April 2013 - 09:19 AM, said:

kgtys, on 21 April 2013 - 12:25 AM, said:

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

You might try slicing almost all the way through the pot when it is almost leather hard, let it dry further then slice all the way through. Make sure you low fire for a couple hours...OR.... put it in your oven and take it from 100F to 350F in 3 hours....Slow drying will help it to not crack further . Cathy

[kgtys]

kgtys, on 21 April 2013 - 04:12 PM, said:

Posted Today, 10:25 PM

Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

[kgtys]

Thanks Cathy - that sounds manageble for me!


Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.
[/quote]

You might try slicing almost all the way through the pot when it is almost leather hard, let it dry further then slice all the way through. Make sure you low fire for a couple hours...OR.... put it in your oven and take it from 100F to 350F in 3 hours....Slow drying will help it to not crack further . Cathy
[/quote]
[/quote]

[kgtys]

[quote name='Chris Campbell' date='21 April 2013 - 01:15 PM' timestamp='1366575332' post='33348']

Chris Throws Pots, on 21 April 2013 - 01:57 PM, said:

Check out Jeff Campana's work. http://jeffcampana.com/

Thanks for this link ... Terrific work and a most interesting process.

Thanks Chris - beautiful stuff!

[kgtys]

kgtys, on 21 April 2013 - 04:35 PM, said:

Thanks Cathy - that sounds manageble for me!


Hi - I am making my first coil pot - a bowl or maybe a vase - (I am new to this) and wanted to put a decorative crack penetrating the entire thickness (preferably just one if that is possible).
I saw a youtube video of someone using a small hammer after it had been fired(?). The sides looked thin (maybe done on a wheel?) and she made a bigger crack than I would want to do. Should I think of switching to slab to control thickness? Would it be possible to cut the vase in 2 pieces and either intentionally put them back together unevenly before firing, or firing the 2 pieces and then gluing them back together unevenly?
It would be a decorative piece and doesn't need to hold water. As you can see I know nothing about this so any info would be helpful! Thanks-

PS- Here is a pic of the feeling I want for the pot, but maybe just one crack going up the bowl or vase.

You might try slicing almost all the way through the pot when it is almost leather hard, let it dry further then slice all the way through. Make sure you low fire for a couple hours...OR.... put it in your oven and take it from 100F to 350F in 3 hours....Slow drying will help it to not crack further . Cathy
[/quote]
[/quote]
[/quote]

Thanks Cathy - That sounds manageble for me!

[kgtys]

Marcia Selsor, on 21 April 2013 - 10:13 AM, said:

Stephen Lee is the Director at the ARchie Bray and recently open a show in NYC. Some pieces were from this series
http://www.ferringal...nt_8303_374.jpg

Marcia

Thanks Marcia I learn alot form these great visuals!