- Ceramic Arts Daily - http://ceramicartsdaily.org -

How to Make Banding Wheel Pins for Centering Ease

Posted By Jim Wylder On January 21, 2013 @ 9:18 am In Daily,Features,Making Clay Tools | 4 Comments

I am impatient when it comes to centering work on a bat on my banding wheel. But a banding wheel fitted with bat pins could make it easy peasey.

 

In today’s post, an excerpt from the January 2013 issue of Ceramics Monthly, Jim Wylder explains how he retrofitted his banding wheel so that it accepts bats with a standard-sized holes. So smart! – Jennifer Harnetty, editor.

 

 

Click to enlarge!

 

Cut four stay blocks that are ¾ inches wide and 2½ inches long. The stay blocks need to be the same thickness as the edge of your banding wheel. Use the outside curve of your banding wheel to draw a curve on the stay blocks. The curve needs to be cut out of the block so that the block will fit snugly against the edge of the banding wheel (1). I used a jigsaw to cut the curve but it could be filed or sanded to fit.

 

Drill a 1⁄8-inch hole though each stay block. Center the hole left and right and about 1⁄8 inch from the curved edge. This is where the washer and screw fasten the bat to the banding wheel.

 

Center the ¾ inch-thick bat on the pottery wheel. While spinning the wheel at high speed, make a dot in the center—this must be very precise. Draw a line directly through the center. Draw another line directly through the center perpendicular to the first one. You now have an X. The four stay blocks that will keep the bat on center will be glued on using these lines as a guide.

 

Measure your banding wheel diameter (mine was 10 inches.) Draw a circle on the bat (while it is spinning) to match your banding wheel diameter (2). Turn your banding wheel upside down and center it on the bat using the drawn circle as a guide. Spin the pottery wheel and nudge the banding wheel to the exact center.

 


 

Stay up with the latest information throughout the year with a subscription to Ceramics Monthly magazine. Valuable tips like the banding wheel pins in today’s post, gallery reviews, technical updates, techniques, studio tours and more — it’s all there! For inspiration and information, Ceramics Monthly delivers.
 Find out more and subscribe today! 

 

 


 

Click to enlarge!

Position the blocks on the X lines and glue them with the curved side next to the banding wheel. Use tape to hold them while the glue sets (3). Turn the bat over when the glue is dry and center it again on the pottery wheel. Locate the center as before and draw a line through the center. Position this line so that it does not intersect the stay blocks underneath. Make two marks for the bat pin holes on this line. The marks should be 10 inches apart and 5 inches from the center point on the line. Drill a 7⁄32-inch hole ½ inch deep on the marks.

 

Use an Allen wrench to screw in the bat pins (4–5). Notice that the first time they are inserted they will cut the threads in the wood. Putting a little wax on the threads helps. Test fit one of your standard bats. Plasti-bats that are larger than the 12-inch plywood banding wheel head make removing the bat handy. Turn your newly-pinned, wooden banding wheel head over with a bat in place.

 

Put your banding wheel in the opening and secure the plywood to it using the nylon washers and stainless steel screws inserted into the pre-drilled holes in the stay blocks.

 

If a test run reveals that all is as it should be, remove all the hardware, sand it smooth, and coat the wood twice with any finish that will protect the wood (6).

 

 

MATERIALS & TOOLS

 

Banding wheel head: A ¾-inch-thick plywood bat, 12 inches in diameter. This can be either a commercially made bat or a homemade bat.

 

Bat pins: Two bat pins (SS Socket Cap Screw ¼ inch × 20 × 12 course thread, ½ inch long), 7/32-inch drill bit.

 

Stay blocks: Four wood blocks that are the same thickness as the edge of your banding wheel. My banding wheel was ¾ inches thick, so I used ¾-inch plywood cut ¾ inches wide and 2½ inches long.

 

Stay washers and screws: Four 1⁄8-inch thick × ¾-inch nylon washer, four stainless steel no.8 × ¾-inch wood screw, 1⁄8-inch drill bit

 

Tools: Drill, screwdriver, ruler, Allen wrench for the bat pins, jigsaw, wood glue, painter’s tape

 

 

Send your tip and tool ideas, along with plenty of images, to editorial@ceramicsmonthly.org. If we use your idea, you’ll receive a complimentary one-year subscription to CM!

 


 

For more interesting homemade tool ideas, be sure to download Pottery Throwing Tools: A Guide to Making and Using Pottery Tools for Wheel Throwing, which is free to Ceramic Arts Daily subscribers.

 

 


 

 
 

Article printed from Ceramic Arts Daily: http://ceramicartsdaily.org

URL to article: http://ceramicartsdaily.org/clay-tools/making-clay-tools/how-to-make-banding-wheel-pins-for-centering-ease/

Copyright © 2008-2012 Ceramic Arts Daily. All rights reserved.