claytrap_620Fixing a clogged drain is hard work and expensive. Making a drain trap is easier and cheaper than you might think. In today’s post, an excerpt from the April 2014 issue of Ceramics Monthly, Raquel and Dan Sobel explain how to make a clay trap from inexpensive and readily available materials. Give it a try in your own studio. It could save you a lot of trouble.- Jennifer Harnetty, editor.

 


 

I was a little nervous about setting up my own studio in the basement of my house with a 20-year-old septic tank and leach field, so I wanted to make sure my clay trap was really safe. 

 

After researching the subject on the Internet I came across two methods, both with two buckets. Method A used one bucket inside the other and Method B used the two buckets in series. I decided to create (with the help of my engineer son) a more effective clay trap combining these methods.

 


 

Sustainable Ceramics

This new release, by veteran ceramic artist Robert Harrison, sheds a light on the latest studio practices needed to operate responsibly in a changing environment. Discover the latest developments in managing your studio resources from materials to firing. Robert, a key leader of NCECA’s Green Task Force brings together a wealth of information every responsible potter should be aware of.

 

Read more and download an excerpt!

 

 


 

MaterialsMy system consists of one large plastic tote box with two smaller buckets inside it. The water flows through the system from bucket to bucket, creating three sediment settling stages. From the sink, the water flows into the first small bucket, then into the second small bucket. It exits the second bucket via a cluster of small holes into the large tote box, from which it flows to the outlet pipe on the opposite side. This setup ensures that a minimal amount of clay will enter my drainage pipes.

 

It is critical that the exit hole is lower than the entrance hole in each container and that the pipes are all slanted slightly downward so that the water flows through the system correctly. I also recommend placing the exit holes on the opposite side of the container from the inlet hole to allow the sediment to settle properly.

 

The drainage pipe out of my house is higher than my clay trap discharge pipe so I had to pump the water to the sewer line in my basement using a sink utility pump.

 

This clay trap has been effectively saving my pipes and septic tank for almost a year now. Sediment builds up in all three stages, but in lower quantities in the later stages. The easily removable lid keeps the odor minimal, while allowing for easy access to periodically remove the settled clay.

 

Image1

Procedure

Lay out the buckets in their intended positions. If needed, a pallet or 2×4s can be placed under the tote to raise it to the proper height. Mark where the holes should be drilled based on the reference diagram. Remember that the pipes need to be slightly slanted so that water flows in the correct direction. In general, the inlet hole should be at least ½ inch above the outlet hole for each container.

 

On the first small bucket, use the 1½-inch-diameter hole saw to drill the holes on opposites walls and opposite ends of the bucket. The first hole should be as high as possible on this bucket. On the second small bucket, drill the 1½-inch-inlet hole on the side next to the other small bucket hole and drill around 10 small drainage holes using a ¼-inch-drill bit in the side wall opposite the drainage from the big tote. On the large tote box, drill one 1½-inch-hole to allow the pipe from the sink to the first small bucket to pass through, and one hole for the pipe leading out to the drainage connection.

 

Image2Assemble the PVC pipes from the sink through the tote into the first small bucket, from the first small bucket to the second small bucket, and from the tote to the outlet drain. Apply the PVC primer and cement according to directions on the containers to glue the pipes in place. It is best to have a professional plumber connect the clay trap to the sink and to the outlet drain. Use silicon sealant to seal all the holes after the pipes are in place. Finally, use a sink strainer to prevent large items from entering the pipes.

Clay-Trap-Diagram

 

Send your tip and tool ideas, along with plenty of images, to editorial@ceramicsmonthly.org. If we use your idea, you’ll receive a complimentary one-year subscription to CM!


 

To learn how to add texture to your work, download your free copy of 
Ceramic Carving Tool Techniques: Bringing the Ceramic Surface to Life!
 
 

 

 


 

 
 
Click here to leave a comment