I just love the sugary matt surfaces, color schemes, and subtle layers in Kristin Pavelka’s work. Kristin uses gorgeous red earthenware to her advantage by creating linear sgraffito marks through white slip. Then she creates subtle layers of glazes — often using two tones of the same color — in a paint by number fashion. The result is work that looks as yummy as a frosted sugar cookie.

In today’s post, Kristin explains these decorating techniques. She also shares glaze and slip recipes! – Jennifer Harnetty, editor.

 

figure 7. Pour white slip onto the middle of the plate, turning the piece clockwise until the entire face is covered.
figure 7. Pour white slip onto the middle of the plate, turning the piece clockwise until the entire face is covered.

Decorating with Slip and Sgraffito

I slip my pots when they look dry but have a small bit of moisture in them. This allows for a relatively even coating of slip, yet it dries a bit slower giving me time to complete my sgrafitto before the slip starts to chip when scratched. Because the slip dries quickly, I have to work fast to complete my design, so I plan the patterns ahead of time in a sketchbook or by drawing with a soft pencil on the unslipped plate itself.

 

Once I’ve decided on a pattern, I can begin slipping. Holding the plate vertically, I pour the white slip onto the middle of the plate using a large ladle, turning the piece clockwise until the entire face is covered (figure 7). Keep the plate vertical until the slip drips have firmed, then rest the plate on the tabletop and allow the slip to dry for a few minutes until you can touch it without a fingerprint remaining, but while it still feels cold and damp.

 

figure 8. Scratch through the slip so that the tool just barely digs into the underlying clay.

Lightly draw a grid on the piece using a soft pencil, like a 2B. Breaking up the space symmetrically on a circular form is a quick and easy way to understand the space. I sometimes draw my pattern on the piece to double check the placement of key elements, but usually I draw directly with my sgraffito tool using just the grid as an aid for placing the design.

 

My sgrafitto tool had a previous life as a dentistry tool and is thicker and duller than a standard needle tool. A long nail with a dull point is a good substitute. The line created is thicker than an X-Acto blade or needle tool and can give a similar line quality as a standard-sized pencil lead. Medium pressure is exerted with the tool tip so that it scratches through the white slip and just barely digs into the red underlying clay (figure 8). I brush a stiff yet soft-bristled brush across the surface of the plate once the design is carved to clean up the edges of the incised lines as well to rid the surface of the slip crumbs (figure 9).

 

figure 9. Brush the surface once the design is complete to clean up the edges of the incised lines.

figure 9. Brush the surface once the design is complete to clean up the edges of the incised lines.

Finally, a Scotch Brite pad is lightly rubbed along the rim to help expose the red earthenware beneath. This helps create more depth in the surface once it has gone through the glaze firing.

Note: For all three of the above steps that create crumbles or fine powder, wear a mask and work over a bucket of water to minimize the amount of dust entering the air and to make clean-up easier.


Create surfaces that will turn heads!

Erin Furimsky shows you how in her Layered Surfaces DVD!


figure 10. Load up a small brush with the darker-toned glaze and fill in the pod shapes on the bisque-fired plate.
figure 10. Load up a small brush with the darker-toned glaze and fill in the pod shapes on the bisque-fired plate.

Glazing by Numbers

I bisque fire to cone 01, then, to prepare the piece for glazing, give it a good shower under running water to clean any leftover sgrafitto dust from the surface. Leave the piece to dry overnight. The first glaze application is much like a paint-by-number painting. Often using two tones of the same color, I’ll load up a small brush with the darker tone and fill in the “pod” shapes. Little pressure is used when painting as the glaze should flow from the brush onto the bisque, eliminating brush strokes (figure 10). I fill the sgrafitto lines with this first glaze, which helps eliminate pinholes in the glaze-fired impression. This first layer of glaze is left to dry several hours to overnight.

 

The second, lighter tone of glaze is then poured on the plate in a similar fashion to the white slip—rotating a vertically-held plate clockwise while pouring the glaze in the middle of the piece (figure 11). This second coat is left to dry.

 

figure 11. Once the first glaze is dry, apply a coat of a lighter-toned satin glaze using the same technique as for pouring the slip.
figure 11. Once the first glaze is dry, apply a coat of a lighter-toned satin glaze using the same technique as for pouring the slip.

The final glazes are now ready to be applied to the dots using a small soft brush or a fingertip. I can usually see a light indentation of the sgrafitto dot through the poured glaze to use as a guide for dot placement. If I am unable to determine where to place my dot within the design, I sometimes guess and other times fire the piece and then apply the dots to the fired glaze and refire. The final dots are made up of a lighter-toned large dot with a smaller dark toned dot on top (figure 12).

 

The dry, glazed piece is fired to cone 04, held at that temperature for 15 minutes and then fired down to cone 010 before being turned off. This schedule helps to produce a nice satiny finish to the glaze surface.

Kristin Pavelka is a full-time studio potter living in Maplewood, Minnesota. To see more of her work visit www.pavelkapottery.com.

 

figure 12. Apply the accent glazes, starting with the lighter glaze, and finishing with small dots of darker glaze.

figure 12. Apply the accent glazes, starting with the lighter glaze, and finishing with small dots of darker glaze.

 

 

 

glaze recipes

Recipes: click to enlarge


For more great low fire glaze recipes, be sure to download your free copy of 15 Low-Fire Glaze Recipes from the Pros: Recipe Cards for Low Fire Pottery Glazes.
Click here to leave a comment